10-Pin Split Cable

$30

Part Number: TP240212

Availability: In-Stock

The 10-Pin Split Cable attaches to the ribbon cables on the Aardvark™ I2C/SPI Host Adapter, the Cheetah™ SPI Host Adapter, the Beagle™ I2C/SPI Protocol Analyzer, and the Promira Serial Platform. The 10-Pin Split Cable is an ideal solution if you don’t have space for a 5x2 0.100" header on your test board and need individual leads for each pin. It also allows use of a header that doesn't have the same pin-out as your Total Phase host adapter/protocol analyzer.

Receive a 15% discount on this product when purchased with any host adapter, interface, protocol analyzer, or development kit
Offer limited to 3 accessory cables for each host adapter, interface, protocol analyzer, or development kit purchased

Key Features

Includes a 10-pin box header that attaches to the ribbon cable

Connector is a standard 5x2 0.100" (2.54mm) pitch IDC type keyed box connector

Cable will connect to any standard 0.100" (2.54mm) pitch 10-pin keyed IDC-type connector

Cable is 5 inches (12.7cm) long to minimize signal degradation

Each individual lead is terminated with a single pin crimp connector with the same 0.100" (2.54mm) pitch

Each individual lead has a different color and is labeled with the pin name for easy identification

Tech Specs

Lead Pin-Out

Each lead is color coded and has a small label to indicate which lead is associated with which pin. The lead pin-out is shown in the following table.

I2C/SPI	eSPI	#	#	I2C/SPI	eSPI
SCL/GPIO00	Alert0	1	2	GND	GND
SDA/GPIO01	Alert1	3	4	VTGT	VTGT
MISO/IO1	IO1	5	6	VTGT	VTGT
SCLK	SCK	7	8	MOSI/IO0	IO0
SS0/GPIO02	CS0	9	10	GND	GND

Bit Rate

I2C Master: 1 kHz - 800 kHz
SPI Master: 125 kHz - 8 MHz
SPI Slave: 0.1 MHz - 4 MHz

Resources

User Manual

Quick Start Guide

Downloads

Support

Datasheet

Related Products

Reviews

1

Heather

Helpful connector for Promira

2022-05-12

This should be easier to find for ordering. It is very helpful when using the Promira device.

Sam Bruner

Excellent Tool

2022-03-21

Helpful for adapting from the 10 pin connector at the end of an Aardvark to individual header pins. Can also be adapted to gator clips with the right adapters (sold separately)

Deanna D.

Satisfied

2019-02-06

Satisfied with my purchase.

Tun L.

fast respond and shipment

2018-11-21

fast respond and shipment

sylvain c.

great

2018-07-11

great

John G.

4.7 Stars

2018-07-08

But I wasn't offered that resolution. An absolute project-saver. I have but two gripes. One is that each time one switches modes, the "protocol lens" has to change. The software does it automatically, but reminds the user each time, requiring dismissal of a dialog. Why isn't it silent? The other is a scroll lock button, which when depressed allows the display to scroll. But the button doesn't stay in that position. If one uses the cursor to examine data in the scrolling window, the button unlocks. These annoyances are minor. I would absolutely purchase another of these analyzers (even if I had to spend my own money!)

Yuriy K.

10-pin Split Cable

2018-02-07

Great product if your board does not have 5x2 header, but use individual SPI or I2C bus connection.

William R.

K Team

2017-08-14

Service is great but repeat orders should be able to use PO's and net 30 terms. Credit Cards are PIA

xinyu l.

Good

2015-10-14

easy to ise

Ken H.

The cable that we purchased from you

2014-05-27

The 10 pin cable is exactly what we needed for this project. It works well and we would recommend this product to anyone who might need it.